![]() Solution 3: Update Xbox 360 Controller drivers And here you can fix USB port not working issue on Windows 10. You can try to plug your Xbox 360 Controller into many different USB ports to test it, in this case, you may also be able to fix the Xbox 360 Controller blinking or flashing issues by reconnecting the Xbox 360 Controller to a different USB receiver. If the battery is in good condition, now you can try to plug your Xbox 360 Controller to another USB 2.0 or 3.0 port to check if it is the broken USB port that resulted in this Xbox 360 Controller not having a steady connection with Windows 10. But also if you are rechargeable battery consumer, you can just recharge the battery pack to see if the Xbox 360 Controller is working correctly. ![]() Or if you are using the Xbox wireless 360 Controller, you are advised to replace the former one with a new wireless Xbox 360 Controller battery pack. To complete this step, you can choose to insert a new AA battery pack into the Xbox 360 Controller. You should at first make sure the batteries of the Xbox 360 Controller is working properly on Windows 10. Solution 1: Check Xbox 360 Controller battery Now it is the time for curing this Xbox 360 not working disease. ![]() Just as you can imagine, the not working or not connected Xbox 360 Controller can be caused by the Xbox 360 Controller peripheral going wrong and the Xbox 360 Controller driver issues. But how to fix the Xbox 360 wired or wireless Controller not working on Windows 10/11 is far beyond your capacity. It is conceivable that you are very upset about its failing to work or sometimes, it is detected by Windows 10 but not configured when you are combating in a game. However, at the same time, you must be familiar with the scene that when you were playing the computer games, the Xbox 360 Controller suddenly stops working or works with a blinking / freezing buttons or cannot connect to the console. ![]() * In the Search for Driver Software in This location Enter the path where the xusb21.inf file is then click next.ĩ: The Driver should now install with no problems, what we did by changing the ids was tell windows that this software is for our hardware device and to use it.As Xbox 360 Controller passionate lovers, you can enjoy the great convenience it brings you. * In the Driver Tab Click update Driver, Click Browse My Computer for Driver Software * Once you have entered these details click Replace all, once done close and save the document.Ĩ: * Now go back to the properties of your control from device manager * In the Replace with box Hold CTRL and tap P this should paste the hardware ID that we copied from our control. * Click Edit in the Menu and go down and click replace, Type in the Hardware id next to Wired Common Controller in the Find what box it should start with USB\VID. We want to search this entire file for that id and replace it with the one we copied from our control. * Now you should see somewhere near the top of this document “Supports the following Devices” and under that heading Wired common controller and next to it a hardware id. * Once you click on the appropriate id copy the number to clip board (Hold down the CTRL button then tap the C button while doing so.)Ħ: * Now go to the folder where you unpacked the Microsoft Accessories Pack And follow this path “Xbox360\setup64\files\driver\win7\” now setup64 might be setup86 depending on your system setup and there is a choice between operating systems either vista or win 7 so pick the appropriate folder.ħ: * Now this is the driver path and you should see a file called xusb21.inf open this file with notepad * In the properties dropdown box select Hardware ids.ĥ: * Now Two sets of numbers would appear we are after the set that does not contain the REV, but if that is the only one you have it should be fine to select it. * Right Click on the control and click Properties and click the Details Tab. Then the following may help.ġ: * Download the Microsoft Xbox Accessories Driver from Microsoft.Ģ: * Unpack the Microsoft Xbox Accessories Pack Execution File to a temporary Location Using WinZip (Should be able to right click on the file and click extract to…)ģ: * Now Open Device manager (Right Click on Computer in Start Menu and Click Manage, Device manager will be on the left under System Tools)Ĥ: * Now Plug in your control and wait for it to appear in device manager (normally under the Universal Serial Bus Controllers, Mind you it might be under human Interface devices) If your 3rd party Wired Xbox controller is not being fully detected by windows and you have tried the drivers etc. No need to post your comments I have figured out a solution.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |